Granite
Hard and dense, it takes a deep edge polish but needs sharp tooling and slow, steady cuts.

Temecula Custom Countertops provides countertop fabrication in Temecula, CA and across Riverside County, working granite, quartz, marble and quartzite in our own shop. We cut the openings, shape the edges, polish every face and deliver pieces that fit the room they were measured in.
Get a free measure or a bid
Fabrication is the stage where a raw slab becomes a countertop, and it happens in our shop, not on a subcontractor's schedule. We turn your measurements into a cut plan, saw each piece to size, shape the edges, open the sink and cooktop holes and polish every visible face. The pieces leave the shop only when we are satisfied with them.
Because the crew that took your measurements also builds the tops, no detail gets lost between the room and the shop. We fabricate for Temecula, Fallbrook and French Valley homes, and for businesses and builders who send drawings, from a single vanity top to a full kitchen with an island.
How we work
Homeowners get a free measure. Wineries, restaurants, offices and builders get a bid from their drawings.
A slab arrives as a large flat sheet of stone, usually far bigger than any single countertop, and fabrication is the process of turning it into exact pieces. The work follows a fixed order because each step depends on the one before it. A mistake in the layout cannot be fixed by good polishing later, so we spend the most care at the start.
We begin with the template and the slab you selected. The cut plan places every piece on the stone so that the veining and any colour shift run the direction you want. Then the saw cuts the slab down to rough pieces, and a wet-cutting process keeps the stone cool and the dust out of the air. After that come the edges, the cutouts and the polish.
Every step happens before the top reaches your house, so installation day is about fitting and setting, not fixing.
Each stone cuts and polishes differently, and a fabricator who treats them all the same ends up with chipped corners and dull edges. Knowing how a material behaves under the blade is half of the skill, so the approach changes with every slab that comes through the door.
Hard and dense, it takes a deep edge polish but needs sharp tooling and slow, steady cuts.
Engineered and uniform, it cuts cleanly and gives consistent colour across seams, though it must be supported well near cutouts.
Soft and easily chipped, it gets gentler handling and extra support around openings and thin sections.
Harder than most granite, it wears blades fast, so the shop works it patiently to keep edges crisp.
The edge is the part of a countertop your hand and your eye meet most, and it sets the tone of the whole kitchen. A straight eased edge is clean and modern, with only the sharp corner softened. A bevel adds a small angled cut along the top, which gives a crisp, faceted line. A bullnose rounds the edge completely and is friendly to children and to hips that brush past it.
An ogee follows an S-shaped curve and suits traditional kitchens that want detail. A mitered or built-up edge joins two strips so a thin slab reads as a thick, substantial one, which is why it appears on so many islands. A waterfall edge turns the stone ninety degrees and carries it to the floor.
Some profiles are harder to cut in certain stones. A very detailed ogee in a brittle or thin slab can chip, and we will tell you if a profile asks too much of the material you chose. We bring edge samples to the measure so you can feel them, because a drawing never shows how an edge sits under your forearm.
Openings are where a countertop is most likely to fail, so we treat them carefully. A sink cutout is cut to the actual model, with the template taken from the fixture or its spec sheet, and the inside corners are rounded so stress does not gather in a sharp angle. Cooktop and faucet openings follow the same rule. We leave enough stone in front of and behind each hole so the piece stays strong.
Slabs have a limited size, so long runs and large islands often need a seam. We position seams where they are least visible and least stressed, away from the sink and dishwasher where we can, and we match the grain across the joint.
The same shop makes backsplashes, window sills, fireplace hearths and shower curbs from the same slab, so the colour and pattern carry through the room. A matching splash cut from your top's offcut is often the cleanest finish.
Hard water around Temecula leaves mineral film at faucets, so we polish openings smoothly, which also makes them easier to wipe down.

Cutting stone inside a home is messy and imprecise, which is why we do the heavy work in the shop. Slab saws, polishing tools and a level bench give a result that a portable setup in your garage cannot match. The stone stays cool, the edges come out consistent, and the dust never reaches your cabinets.
A controlled setting also lets us catch problems early. If a slab has a hidden crack, we find it on the bench, not after it is on your cabinets. If a piece is a few millimetres off, we correct it before delivery. And because the shop is local, a small change after the template is a quick fix rather than a reorder from another state.
Fabricating in-house also keeps the schedule honest. We control the queue, so we can tell you when your pieces will be ready, and we are not waiting on a broker who is waiting on a plant. When the tops are done, the same people load them, carry them in and set them.
If you bring us a slab you bought elsewhere, we can often fabricate it, though we inspect it first and explain any risks in the stone before we cut.
Fabrication is priced by the piece and the detail, and the figures here are estimates only. As a guide, installed countertops including material are often estimated at about $50 to $120 per square foot, with the stone itself driving most of the spread. If you supply your own slab, the shop work is quoted separately, and the written quote sets the final number.
A free measure is how you get the real number, since the details of your kitchen decide it.
Every top gets a close look before it goes on the truck. We check that edges are even and polished, that corners are square, that cutouts match the fixtures and that the faces are free of chips and scratches. Pieces that share a seam are laid together to confirm the pattern flows and the joint closes cleanly.
On delivery day we protect your floors, carry the stone in on its edge, and check the fit against the cabinets again. If something is off, the shop is close enough to fix it quickly. After the set, we show you how to clean and seal the stone, and you can call us if a mark or chip shows up later.




The process
The saw stays idle until you have seen your slab and agreed to the layout drawn on it.
Tell us the room, the stone and the edge you are considering. Businesses and builders send drawings.
You pick the slab, and we mark seams, edges and cutouts on it for your sign-off.
We cut the pieces wet, shape and polish the edges, and open every sink and cooktop hole.
After a dry-fit in the shop, the same crew delivers, sets the tops and closes the seams.
Questions
In our own shop. The stone is cut, edged and polished there, and the same crew that measured your kitchen delivers and sets the finished pieces.
It depends on the stone, the layout and the shop queue. Expect a delivery date in the written quote, and because the shop is nearby, a small change does not turn into a long wait.
Yes, and we ask you to. Natural stone varies, so you approve the actual slab and the seam layout drawn on it before any cutting begins.
Eased and beveled edges suit modern rooms, bullnose is soft and classic, and ogee reads traditional. Built-up and waterfall edges make a bold island. We bring samples.
Often yes. We inspect it for cracks and flaws first and explain any risk in the stone, then quote the shop work separately.
Yes. We cut splashes, sills and hearths from the same slab so colour and veining carry through, which is usually the cleanest look.
Yes. Send drawings and we bid the job, whether it is a bar top, a reception desk or a run of kitchens for a development.
Book a free measure. We check the cabinets, note every cutout and edge, and the written quote follows.
A free measure for homeowners, and a written bid from drawings for businesses and builders.
Licensed, bonded & insured · License #585047. Calls only, we do not receive text messages.